Authorized Appliance Repair in Colwich, KS

If your KitchenAid refrigerator is frozen on the back, it could be due to a few possible reasons. While I cannot access the specific link you provided, I can offer general guidance to address the issue.

One common cause of freezing at the back of the refrigerator is poor airflow. When the vents or air passages are blocked by food items, the cold air cannot circulate properly, leading to a buildup of frost and ice. To learn more about this issue and potential solutions, you can visit the following link: Why is My KitchenAid Refrigerator Frozen on the Back?

Another possibility is a faulty defrost system. The defrost system in a refrigerator is responsible for melting the ice that forms on the evaporator coils. If the defrost heater, defrost thermostat, or defrost timer fails, the ice may accumulate on the coils and eventually spread to the back of the refrigerator.

A damaged or worn-out door gasket can also contribute to freezing at the back of the fridge. A faulty gasket can allow warm air from the surroundings to enter the refrigerator, causing excessive condensation and frost buildup on the evaporator coils.

Lastly, incorrect temperature settings can lead to excessive cooling and freezing. Ensure that the temperature settings in your refrigerator are properly adjusted according to the manufacturer's recommendations.

If you have checked these potential causes and the issue persists, it is recommended to consult a qualified technician or contact KitchenAid customer support for further assistance.

To reset your Whirlpool washing machine, you can follow a few steps. While I cannot access the specific link you provided, I can provide you with general guidance.

Turn off the washing machine: Ensure that the washing machine is powered off and unplugged from the electrical outlet. This step is important for safety purposes.

Wait for a few minutes: Give the washing machine a few minutes to fully power down. This pause allows any residual power to dissipate and ensures a complete reset.

Plug in the washing machine: After the waiting period, plug the washing machine back into the electrical outlet.

Select the reset option: Look for the reset button or combination of buttons on your Whirlpool washing machine's control panel. The location and specific steps may vary depending on the model. Refer to the user manual or instructions provided by Whirlpool for detailed information. Press the reset button(s) as instructed.

Wait for the reset to complete: Allow the washing machine a few moments to reset itself. You may notice lights blinking or the display changing during this process.

Start a test cycle: After the reset is complete, you can run a test cycle to ensure that the washing machine is functioning properly. Follow the instructions in your user manual or refer to Whirlpool's guidelines for initiating a test cycle.

For more detailed and model-specific instructions on how to reset your Whirlpool washing machine, you can visit the following link: How Do I Reset My Whirlpool Washing Machine?

Please note that the provided information is general in nature. It is always recommended to consult the user manual or refer to official Whirlpool resources for specific instructions tailored to your washing machine model.

If water is leaking from underneath your Sub-Zero appliance, it can be caused by several factors. While I cannot access the specific link you provided, I can provide you with general information to help address the issue.

Clogged or frozen defrost drain: A common cause of water leakage is a clogged or frozen defrost drain. Over time, debris or ice can accumulate in the drain line, causing water to back up and leak out. Clearing the drain line is often necessary to resolve this issue.

Damaged or clogged water supply line: If your Sub-Zero appliance has a water dispenser or ice maker, a damaged or clogged water supply line could be the culprit. Inspect the water supply line for any signs of damage or blockage and replace or clean it as needed.

Improper leveling: Ensure that your Sub-Zero appliance is properly leveled. If it is tilted or not balanced, water may collect and leak from underneath. Adjust the leveling feet or refer to the user manual for instructions on how to level the appliance correctly.

Malfunctioning water inlet valve: A faulty water inlet valve can lead to water leakage. The valve controls the flow of water into the appliance, and if it is not functioning properly, it may cause leaks. In such cases, it may be necessary to replace the water inlet valve.

For more detailed information and specific troubleshooting steps related to water leakage from your Sub-Zero refrigerator, I recommend visiting the following link: My Sub-Zero Refrigerator is Leaking Water. This resource can provide you with more targeted guidance to address the specific issue you are facing.

Please note that while these general tips can help address common causes of water leakage, it is always recommended to consult the user manual or contact Sub-Zero's authorized service technicians for proper diagnosis and assistance with your specific appliance model.

If your dishwasher is not draining, there could be a few potential reasons for this issue. While I cannot access the specific link you provided, I can offer general guidance to help you troubleshoot the problem.

Clogged drain filter or food debris: A common cause of dishwasher drainage problems is a clogged drain filter or food debris blocking the drain pump or hose. Check the dishwasher's filter, located at the bottom of the dishwasher, and clean it if necessary. Additionally, inspect the drain pump and the hose leading from the dishwasher for any obstructions and remove them.

Air gap or garbage disposal clog: If your dishwasher is connected to an air gap or garbage disposal, ensure that these components are not clogged. A clog in the air gap or garbage disposal can restrict proper drainage. Clean them out if needed.

Faulty drain pump: A malfunctioning drain pump can also prevent your dishwasher from draining. Listen for any unusual noises coming from the pump during the drain cycle. If the pump is not working properly, it may need to be replaced.

Blocked drain hose: Check the drain hose for any kinks, twists, or blockages. A blocked or improperly installed drain hose can impede proper drainage. Straighten out any kinks and ensure that the hose is properly connected to the drain or garbage disposal.

For more detailed information and specific troubleshooting steps related to dishwasher drainage issues, I recommend visiting the following link: Why is My Dishwasher Not Draining? This resource can provide you with more targeted guidance to address the specific issue you are experiencing.

Please note that the provided information is general in nature. If the problem persists after following these troubleshooting steps, it is advisable to consult the user manual or contact a qualified technician or the dishwasher's manufacturer for further assistance.

If your garbage disposal won't run, there could be a few possible reasons for this issue. While I cannot access the specific link you provided, I can offer general guidance to help you troubleshoot the problem.

Power supply issue: Check if the garbage disposal is receiving power. Ensure that it is plugged in properly and that the circuit breaker or fuse connected to it has not tripped. If there is no power, reset the circuit breaker or replace the fuse.

Reset button: Most garbage disposals have a reset button located on the bottom or side. Press the reset button to reset the unit and see if it starts running.

Overloaded or overheated motor: If the garbage disposal is overloaded or overheated, it may automatically shut off. Allow it to cool down for a few minutes, then press the reset button. Avoid overloading the disposal in the future.

Jammed impellers: Sometimes, the garbage disposal's impellers can become jammed by debris or objects. Ensure the power is turned off, and using a wrench or a special disposal tool (if provided), try to manually rotate the impellers to dislodge any obstructions.

Faulty wiring or switch: Inspect the wiring and switch connected to the garbage disposal. If there are any signs of damage or loose connections, it may be necessary to repair or replace them.

For more detailed information and specific troubleshooting steps related to a garbage disposal that won't run, I recommend visiting the following link: Why Won't My Garbage Disposal Run? This resource can provide you with more targeted guidance to address the specific issue you are experiencing.

Please note that the provided information is general in nature. If the problem persists after following these troubleshooting steps, it is advisable to consult the user manual or contact a qualified technician or the manufacturer of the garbage disposal for further assistance.